Yurt Forum - A Yurt Community About Yurts  

Go Back   Yurt Forum - A Yurt Community About Yurts > Building a Yurt
Search Forums
Advanced Search

Placing Twin-yurts On A Single Wooden Platform

Reply
 
Thread Tools Display Modes
Old 03-08-2014, 09:52 AM   #1
Yurt Forum Youngin
 
Join Date: Mar 2014
Posts: 4
Default Placing twin-yurts on a single wooden platform

We have started constructing the wooden base for our twin yurts (27m2 and 15m2) which a carpenter is making out of good quality 22cm wide wooden strips cut into 1.5m x 2m sections which will all link together and sit ontop of cement blocks. The final structure is 77m2, measuring 7m x 11m.

We want to place the yurts on top of this structure but need to come up with a way of waterproofing the yurts where they meet the floor.

The floor has 5mm gaps in between the 22cm wide planks which will allow for drainage outside the yurts.

We are thinking of adding a lip all the way round the yurts, perhaps waterproofed with silicon or are wondering whether we should cut a circular drainage hole into which the yurts would be pulled and fastened so the rain can drain away.

Does anyone have any experience of placing yurts on one single wooden platform? We plan on only having the yurts up Spring to Autumn.

Thanks in advance,

Ed, South of France


Last edited by tisseyres-yurts; 03-08-2014 at 09:55 AM.
tisseyres-yurts is offline   Reply With Quote
Old 03-08-2014, 10:53 AM   #2
Yurt Forum Addict
 
Join Date: Nov 2013
Posts: 2,155
Default Re: Placing twin-yurts on a single wooden platform

Here are some ideas.

One way if you have the cash. Frame a seperate

yurt platform

atop the deck. Frame with 2x4s on edge. Insulate with sheet foam fitted tight between the 2x4 joists. Lay foam atop spacers. Cover with 2x6 decking. Your yurts will be elevated 5" off the deck with cover drape of 5" at the edge. The main deck is self draining.

Another way without

insulation

. Build a second 2x6 yurt floor atop the new platform. Lay the 2x6 flat, and install perpendicular to the main deck. That will stop the majority of air leaks through the floor as well. 1.5" of elevation will stop water into the yurt.

A cheap way. Rout a 1" wide by 1/2" deep moat around the perimeter. Anchor the wall lattice just inside the moat. Water drains in the slots at the moat. Add 1" dia. drain holes.

Apply one good thick prime coat to all boards before framing.

Good luck.
Bob Rowlands is offline   Reply With Quote
Pacific Yurts - The original modern yurt
Old 03-08-2014, 11:18 AM   #3
Yurt Forum Addict
 
Join Date: Nov 2013
Posts: 2,155
Default Re: Placing twin-yurts on a single wooden platform

Another cheap way using roll flashing and a router. Pencil the wall diameter on the 2x6 deck. Rout a 1/4" wide slot, 1/2" deep into the deck on that line. The easy way to do this is to attach a long strip to the bottom of the router and anchor it to the focus of the circle. Just swing the router and you'll have a perfectly round slot.

Paint the slot. Install roll flashing vertically in the slot, and toe screw from the outside in through the slot, into the interior yurt floor. Install the screws on an angle, like toe nailing. Drill a pilot hole first, and use plated screws. Install wall lattice so it butts into the flashing on the inside. The cover drapes over the outside face of the flashing.
Bob Rowlands is offline   Reply With Quote
Old 03-09-2014, 02:52 AM   #4
Yurt Forum Youngin
 
Join Date: Mar 2014
Posts: 4
Default Re: Placing twin-yurts on a single wooden platform

Thanks Bob.

Much appreciated!
tisseyres-yurts is offline   Reply With Quote
Old 03-09-2014, 04:06 PM   #5
Yurt Forum Addict
 
Join Date: Nov 2013
Posts: 2,155
Default Re: Placing twin-yurts on a single wooden platform

Yet another way to install the roll flashing vertically in the deck floor, without using a router, is to simply use your skilsaw to cut the penciled wall diameter line. The saw kerf will be wide enough to insert the roll flashing. Set the blade for 5/8ths depth. Tuck the flashing into the saw kerf, and screw/anchor as above. If you wanted to get real fancy, you could pump silicone caulk into the saw kerf prior to installing the flashing. That would give a water tight joint. Installing the flashing in this manner would go much easier with two guys, and two cordless drill. One drill setup for drilling the screw pilot hole, and the other to drive the screw home.

I'm frugal myself. For economy reasons I'd likely try this last method first. If it doesn't work that well, try the elevated platform approach.

Good luck.
Bob Rowlands is offline   Reply With Quote
Old 03-09-2014, 04:09 PM   #6
Yurt Forum Addict
 
Join Date: Nov 2013
Posts: 2,155
Default Re: Placing twin-yurts on a single wooden platform

Make that, "wall circumference line", not "wall diameter line".
Bob Rowlands is offline   Reply With Quote
Reply

Tags
None

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -5. The time now is 05:58 AM.


Yurt Forum | Buying a Yurt | Building a Yurt | Yurt Life | Yurts for Sale | Yurt Glamping | Yurts Pricing Yurt Calculators | Yurt Insurance | Yurt Insulation | Yurt Classifieds

Copyright 2012 - 2024 Jeff Capron Inc.

Yurt Posts Delivered to your Email!

Stay up-to-date with all the new yurt posts to your inbox!

unsusbcribe at anytime with one click

Close [X]